九游登录入口

    <noscript id="ey0ws"></noscript>
<option id="ey0ws"></option>
  • <dd id="ey0ws"><optgroup id="ey0ws"></optgroup></dd>

    <sub id="ey0ws"><listing id="ey0ws"></listing></sub>
      1. Linchuan Precision specializes in the production and development of SMT steel mesh
        Focus on improving the pass through rate for SMT Enterprises
        Lower production cost
        0755-29749682
        18928403435
        Focus on Improving Direct Pass Rate for SMT Enterprises
        Lower production cost
        Professional design
        Your present position:Home / Design

        For the electronics assembly industry, SMT assembly is a fairly mature process technology, but maturity does not mean that there are no defects. Conversely, with the further miniaturization of electronic component packaging, process issues become more difficult to control. According to authoritative statistics, the most important and critical process in the SMT process should be the solder paste printing process. Almost 70% of the solder defects are caused by poor solder paste printing.


        The solder paste printing process is related to the success or failure of SMT assembly quality. The design and manufacture of steel mesh is a key factor in the quality of solder paste printing. The design can be used to obtain good solder paste printing results, otherwise the process quality will be unstable. The defect problem is difficult to control. The following is to show you the design of Linchuan Precision's common electronic components:


        1, CHIP material components

        The package is a rounded corner of the 0201 component that is 10% in the long direction and has an R=0.03mm. Gap guarantee must not be less than 9 MIL greater than 11 MIL

        The package is 0402 component opening as shown in the figure (when the gap is less than 0.4mm, it needs to be moved to 0.4mm, and when the gap is larger than 0.4mm, it needs to be expanded to 0.4mm)

        The package is 0603 component opening as shown in the figure (when the gap is less than 0.6mm, it needs to be moved to 0.6mm, when the gap is greater than 0.72mm, it needs to be expanded to 0.72mm)


                   image002.gif     image004.jpg            

        The package opening of the package 0805 or higher (including 0805) is as follows:
                    image006.jpg         


        FUSE.MELE opening is as follows:
                               image008.jpg       
         

        The large CHIP material cannot be classified by 90% of the area of the pad, and the amount of tin in the component is adjusted slightly.

        The diode is open at 100% of the pad area. If it is cylindrical, increase the length to ensure a sufficient amount of tin.

        Generally, the PITH value of the component is combined with the standard pad size. For the standard, please refer to the following figure:                                                                                                                                                                         

        CHIP material type judgment comparison table

        Package category(milmm)

        PITCH(mil)

        Standard pad size (length x width)(mil)

        0402(1005)

        P<55

        25×20

        0603(1608)

        55≤P≤70

        30×30

        0805(2012)

        70≤P≤95

        60×50

        1206(3216)

        P=135±10

        60×60

         

        2, small form factor crystal

        SOT23: The pad size is small, to ensure solder quality, the hole is pressed to the pad.1:1.

        SOT89: Use the hole opening method as shown below.

                  image010.jpg   
            
        3, SOT252, SOT223 and other power transistor opening methods are as follows:

              image012.jpg 

        4, SOPSOJ socket connector and other components of the stencil opening design

        PITCH=0.8-1.27mm, W.L is 1:1, and rounded at both ends (the width is generally between 45% and 60%)

        PITCH=0.635-0.65mm, W=0.32mm, L is 1:1 and rounded at both ends.

        PITCH=0.5mm, W=0.24mm, L is 1:1 and rounded at both ends.

        PITCH=0.4mm, W=0.19mm, L is moved outward by 0.1mm, then lengthened outward by 0.05mm and rounded at both ends.

        PITCH=0.3mm, W=0.16mm, L is 0.1mm outward, and rounded at both ends (if the length is <0.8mm, the length is 0.15mm long).

        0.5PITCH QFP, 0.23mm in the width direction, 0.1mm in the length direction, and 0.1mm in the outer direction;

        0.5PITCH QFN, 0.23mm in the width direction and 0.1mm in the length direction;

        The silk screen frame is QFN from the pin, as shown in the following figure;


            image013.jpg          

        If L < 1 mm above, the L needs to be outwardly expanded by 0.1 mm. If the original size of W is smaller than the value of the value, it should be increased when opening.


        5. If the IC is grounded, it needs to be opened:

        The grounding pad in the middle is opened by 60% of the area, and if necessary, the bridge is rounded and rounded with R=0.05mm;

         

        6, exclusion, discharge capacity (such as for the same customer, in the production: W should be unified):

        The width is 48-50% of PITCH, L is 1:1 according to file and rounded at both ends.

        If the pin is <0.8mm, the length is 0.15mm outward. If the gap between the two rows of pins is <0.4mm, the outward movement of each side ensures that the inner gap is 0.4mm.


        7, BGA opening:

         BGA openings can be made with the following references:

        A, in principle, the CIR of the opening is 55% of the PITCH, and if it is SQ, it takes 45% of the PITCH and the R=0.02mm round (except PITCH=0.5mm);

         B, PITCH=0.5mm, CIR=0.30mm or SQ=0.29mm, inverted R=0.02mm fillet;

         C, large BGA opening is divided into three circles, inner ring, inner ring and central part (large BGA distinguishing conditions: Pitch ≥ 1.27mm, number of feet ≥ 256): outer three circles CIR = 0.55 × Pitch, center part 1:1 Opening


        8. When one side of the pad is ≥ 4mm and the other side is ≥ 3mm, the pad should be bridged with a bridge width of 0.4mm.


                        image015.jpg   

        9. Avoid the through hole when the document has a shield:

        Be sure to bridge at the corner, a straight bridge with a width of 0.5mm, and the rest of the length should not exceed 4mm bridge, the bridge width is 0.5mm. The width is extended outward by 0.2mm, and a safety distance of 0.3mm must be ensured with the peripheral pads.

                         image017.jpg   

        10, electrolytic capacitor:

        The length is plus 0.2mm (this type is not used for bridging if there is no special requirement during production)


        11, the way of opening the cable is the same as the modification of the IC.


        12, SIM card and TF deck smt steel mesh opening design:


                 image019.jpg     
        The outer three sides are outwardly lengthened by 0.25 mm, and the length of the pin on the right side is expanded by 0.25 mm in the direction of the arrow. If the width is small, the length can be appropriately increased.


        • Independently developed on-line electrolytic polishing technology, not only safe and environmental protection, but also make SMT printing high through rate: 99%-99.7%.
        • The technical team has rich experience and complete testing equipment. Each steel mesh undergoes six testing procedures.
        • Independent research and development of online electrolytic polishing technology, safety and environmental protection
        • Relying on the company's technology, optimizing the design scheme of customer opening to avoid design risks for customers
        • Purchasing steel mesh is to create value for the company: SMT steel mesh value = steel mesh price - cost saved without repairs - order value increased with customer satisfaction
        • Research and development of next generation products, when customers have orders, can quickly help customers create value, enhance customer market competitiveness.
        • Printing through rate
        • Shift qualitative
        • Electropolishing
        • Technical service
        • Cost performance
        • R&D capability
        • Non-electropolishing or traditional polishing not only pollutes the environment, but also makes the printing pass-through rate low: the pass-through rate is less than 97%.
        • Team instability, no other testing equipment except magnifiers, product shipment sampling or "exemption from inspection"
        • Non-electric polishing or traditional polishing, polluting the environment, does not meet the environmental requirements.
        • Only according to customer documentation production, can not provide any technical services for customers
        • Purchasing steel mesh adds a lot of intangible costs to the company: SMT steel mesh value = steel mesh price + increased cost of repairs + customer dissatisfaction with the value of canceling orders
        • Unable to adapt to the times to update products, so that both their own and customers lose market competitiveness, to bring immeasurable losses to customers.
        Printing through rate
        Independently developed on-line electrolytic polishing technology, not only safe and environmental protection, but also make SMT printing high through rate: 99%-99.7%.
        Non-electropolishing or traditional polishing not only pollutes the environment, but also makes the printing pass-through rate low: the pass-through rate is less than 97%.
        Shift qualitative
        The technical team has rich experience and complete testing equipment. Each steel mesh undergoes six testing procedures.
        Team instability, no other testing equipment except magnifiers, product shipment sampling or "exemption from inspection"
        Electropolishing
        Independent research and development of online electrolytic polishing technology, safety and environmental protection
        No electropolishing or traditional polishing, polluting the environment, does not meet the requirements of environmental protection.
        Technical service
        Relying on the company's technology, optimizing the design scheme of customer opening to avoid design risks for customers
        Only according to customer documentation production, can not provide any technical services for customers
        Cost performance
        Purchasing steel mesh is to create value for the company: SMT steel mesh value = steel mesh price - cost saved without repairs - order value increased with customer satisfaction
        Purchasing steel mesh adds a lot of intangible costs to the company: SMT steel mesh value = steel mesh price + increased cost of repairs + customer dissatisfaction with the value of canceling orders
        R&D capability
        Research and development of next generation products, when customers have orders, can quickly help customers create value, enhance customer market competitiveness.
        Unable to adapt to the times to update products, so that both their own and customers lose market competitiveness, to bring immeasurable losses to customers.
        Hot products
        Linchuan Precision specializes in the production and development of SMT steel mesh
        serving over 3,000 customers in 7 years
        producing over 200,000 high-quality steel meshes.
        Service hotline:0755-29749682/18928403435
        Shenzhen Linchuan Precision Technology Co., Ltd.
        Tel:0755-29749682  18928403435
        E-mail:xjx.smt@163.com
        Customer service QQ:254259787     591431201
        Company Address: 2/F, Block C, Fengrun Building, Huafeng Second Industrial Park, Gushu, Xixiang, Bao'an District, Shenzhen
        粵ICP備17051183號

        Sweep up more excitement
        • 合作伙伴 :
        Menu
        Tel About Us Share
        收縮

        在線客服

        • 客服 點擊這里給我發消息
        • 客服 點擊這里給我發消息
        • 曾小姐
          18928403435
        • 羅先生
          18923768657
        • 掃一掃 更多精彩
        九游会官网 九游会手机app 九游个人中心官网 九游会下载 九游会官网首页进入 ag九游会集团 九游会游戏官方平台 九游会开户 9游会j9.com 九游电脑版官网 j9九游会游戏大厅 九游会j9官网 九游登录入口 九游网页版 九游会游戏首页 九游会开户 j9九游会游戏大厅 九游官网网页版 j9彩票靠谱吗 九游会官网 九游会ag官方网站 九游会是什么平台 九游会官网登录网站 九游会是什么平台 九游会j9官网网址 九游会官网首页进入 九游会登录地址 j9九游会下载官网 j9九游会游戏大厅 九游登录客户端 九游会下载 九游会ag登陆 九游会官网登录网站 九游会ag登陆 九游会官方网站 九游会游戏官方平台 九游会注册 九游会平台网 九游会ag登陆 九游会j9官网平台 九游会官网登录 j9九游会在线平台 九游会j9官网网址 j9九游会在线平台 九游会j9官网平台 九游会开户 九游官网网页版 九游会游戏官方平台 九游会靠谱平台 九游客户端官网 九游会手机平台 九游客户端官网 九游会ag官方网站 九游官网登录首页 九游会j9官网网址 j9彩票是不是黑平台 九游是正规平台吗 九游会注册 j9彩票是不是黑平台 九游会直营 九游在线官方网站 九游会j9官网 九游会平台网 九游会下载 九游会账号登录中心 九游会官网首页 ag九游会集团 九游会靠谱平台 九游会游戏平台 九游会ag手机app J9九游会 九游会官方网站 九游在线官方网站 j9九游会 九游会ag手机app 九游官网网页版 ag九游会集团 九游会j9官网网址 九游会游戏官方平台 九游会官网 九游会注册 九游会ag官方网站 j9九游会手机下载 j9九游会游戏大厅 九游会平台 九游会下载 j9九游会游戏大厅 j9九游会在线平台 j9九游会下载官网 九游会ag登陆 九游会下载 九游会官网首页 九游会官网登录网站 九游客户端官网 九游会ag手机app j9九游会官网 9游会j9.com 九游会官网首页进入 九游会平台下载 j9九游会下载官网
        九游登录下载 ag九游会j9 九游会官网 九游会官网登录网站 九游会靠谱平台 j9九游会在线平台 九游会游戏平台 九游会ag手机app 九游会ag官方网站 九游会j9官网网址 九游会游戏官方平台 九游会j9官网平台 J9 九游会官网jy 九游会官网登录 九游是正规平台吗 九游会手机平台 j9com 九游网页版 九游会官方网站-主页 九游会平台 九游会个人安全中心 九游会游戏首页 九游会登录地址 九游会平台网 九游会是什么平台 九游会平台下载 j9九游会官网 j9九游会 九游登录客户端 九游会app 九游会官网平台 九游游戏账号交易平台 九游会下载 九游登录入口 九游电脑版官网 j9彩票靠谱吗 九游会j9登录 九游会官网首页 九游会ag登陆 九游客户端官网 九游官网登录首页 9游会j9.com j9彩票是不是黑平台 ag九游会集团 九游会官网首页进入 九游官网网页版 九游会开户 九游个人中心官网 九游会注册 j9九游会下载官网 九游网页版登录入口 九游会手机app J9九游会 九游会j9官网 九游会账号登录中心 j9九游会手机下载 九游在线官方网站 j9九游会官网